Continental Steel and Tube Company
Continental Steel and Tube Company
P.O. BOX 030040
Fort Lauderdale, FL, 33303
Phone: 954.332.2290
Fax: 954.332.2296
Email: Sales@ContinentalSteel.com
Website: www.continentalsteel.com
Print Back
3003 is the most widely used of all aluminum alloys. It is essentially commercially pure aluminum with the addition of manganese which increases the strength some 20% over the 1100 grade. Thus, it has all the excellent characteristics of 1100 with higher strength. It has excellent corrosion resistance. It has excellent workability and it may be deep drawn or spun, welded or brazed. It is non heat treatable. Applications: cooking utensils, decorative trim, awnings, siding, storage tanks, chemical equipment.

3003-0
Mill Finish
Paper Interleaved
AMS-QQ-A-250/2 AMS4006 ASTM B209
506450912-497007203-aluminum-coil-2
Unit of Measure
Items Metal and Alloy Plate & Coil
3003-0-020-36-C
Aluminum Sheet and Coil - Series 3003-0 		Metal and Alloy Plate & Coil
3003-0-025-36-C
Aluminum Sheet and Coil - Series 3003-0 		Metal & Alloy Sheet & Plate
3003-0-025-96
Aluminum Sheet and Coil - Series 3003-0 		Metal and Alloy Plate & Coil
3003-0-025-48-C
Aluminum Sheet and Coil - Series 3003-0 		Metal and Alloy Plate & Coil
3003-0-032-36-C
Aluminum Sheet and Coil - Series 3003-0
Material N/A Aluminum
Shapeform N/A Coil N/A Coil N/A Sheets N/A Coil N/A Coil
Series N/A 3003-0
Grade N/A 3003
Preparation N/A Paper Interleaved
Temper N/A Soft
Finish N/A Mill
Thickness N/A 0.02 inches0.508 mm N/A 0.025 inches0.6350 mm N/A 0.025 inches0.6350 mm N/A 0.025 inches0.6350 mm N/A 0.032 inches0.8128 mm
Size N/A 36 x Coil N/A 36 x Coil N/A 36 x 96 N/A 48 x Coil N/A 36 x Coil
Width N/A 36 N/A 36 N/A 36 N/A 48 N/A 36
Length N/A N/A N/A 96 N/A N/A
Sheet Weight per Unit Area N/A 0.285 lbs/ft²1.391 kg/m² N/A 0.356 lbs/ft²1.738 kg/m² N/A N/A N/A 0.456 lbs/ft²2.226 kg/m²
Weight per Sheet N/A N/A N/A 8.554 lbs3.880 kg N/A N/A
Coil Weight per Length N/A 0.855 lbs/ft1.272 kg/m N/A 1.069 lbs/ft1.591 kg/m N/A N/A 1.426 lbs/ft2.122 kg/m N/A 1.369 lbs/ft2.037 kg/m
ASTM Specification N/A AMS 4006 AMS-QQ-A-250/2 ASME SB-209 ASTM B209
Ultimate Strength N/A 16 ksi
Yield Strength N/A 6 ksi
Elongation percent in 2 inches N/A 30
Hardness Brinnel Number N/A 28
Ultimate Shearing Strength N/A 11 ksi
Fatigue Endurance Limit1 N/A 7 ksi
Modulus of Elasticity2 N/A 10.0 x 106 ksi
Resistance to Corrosion - General3 N/A A
Stress Corrosion Cracking4 N/A A
Workability (Cold)5 N/A A
Mechinability N/A E
Brazeability6 N/A A
Gas Weldability7 N/A A
Arc Weldability8 N/A A
Resistance Spot and Seam Weldability9 N/A B
Applications N/A Cooking utensils, chemical equipment, pressure vessels, sheet metal work, builder's hardware, storage tanks
Density N/A 0.099 lbs/in³
Specific Gravity N/A 2.73
  • 1 Based on 500,000.000 cycles of completely reversed stress using the R. R. Moore-type of machine and specimen.
  • 2 Average of tension and compression moduli. Compression modulus is about 2 percent greater than tension modulus.
  • 3 Ratings A through E are relative ratings in decreasing order of merit, based on exposures to sodium chloride solution by intermittent spraying or immersion. Alloys with A and B ratings can be used in industrial and seacoast atmospheres without protection. Alloys with C, D and E ratings generally should be protected at least on faying surfaces.
  • 4 Stress-corrosion cracking ratings are based on service experience and on laboratory tests of specimens exposed to the 3.5% sodium chloride alternate immersion test.
  • 5 Ratings A through D for Workability (cold), and A through E for Machinability, are relative ratings in decreasing order of merit.
  • 6 Ratings A through D for Weldability and Brazeability are relative ratings.
  • 7 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.
  • 8 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.
  • 9 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.