Anodized Aluminum Sheet and Coil

Unit of Measure

Items	5005-H34A-032-48-C Anodized Aluminum Sheet and Coil	5005-H34A-032-48-120 Anodized Aluminum Sheet and Coil	5005-H34A-040-48-C Anodized Aluminum Sheet and Coil	5005-H34A-040-48-120 Anodized Aluminum Sheet and Coil	5005-H34A-050-48-C Anodized Aluminum Sheet and Coil
Material	N/A Aluminum
Shapeform	N/A Coil	N/A Sheets	N/A Coil	N/A Sheets	N/A Coil
Series	N/A 5005-H34
Grade	N/A 5005
Preparation	N/A Paper Interleaved
Temper	N/A H34
Finish	N/A Satin Clear
Thickness	N/A 0.032 inches0.8128 mm	N/A 0.032 inches0.8128 mm	N/A 0.040 inches1.016 mm	N/A 0.040 inches1.016 mm	N/A 0.050 inches1.27 mm
Size	N/A 48 x Coil	N/A 48 x 120	N/A 48 x Coil	N/A 48 x 120	N/A 48 x Coil
Width	N/A 48
Length	N/A	N/A 120	N/A	N/A 120	N/A
Sheet Weight per Unit Area	N/A 0.452 lbs/ft²2.207 kg/m²	N/A	N/A 0.564 lbs/ft²2.754 kg/m²	N/A	N/A 0.706 lbs/ft²3.447 kg/m²
Weight per Sheet	N/A	N/A 18.06 lbs8.192 kg	N/A	N/A 22.58 lbs10.242 kg	N/A
Coil Weight per Length	N/A 1.806 lbs/ft2.688 kg/m	N/A	N/A 2.258 lbs/ft3.3608 kg/m	N/A	N/A 2.822 lbs/ft4.120 kg/m
Ultimate Strength	N/A 23 ksi
Yield Strength	N/A 20 ksi
Elongation percent in 2 inches	N/A 8
Hardness Brinnel Number	N/A 41
Ultimate Shearing Strength	N/A 14 ksi
Modulus of Elasticity¹	N/A 10.0 x 10⁶ ksi
Resistance to Corrosion - General²	N/A A
Stress Corrosion Cracking³	N/A A
Workability (Cold)⁴	N/A B
Mechinability	N/A D
Brazeability⁵	N/A B
Gas Weldability⁶	N/A A
Arc Weldability⁷	N/A A
Resistance Spot and Seam Weldability⁸	N/A A
Applications	N/A Appliances, utensils, architectural, electrical conductor
Density	N/A 0.098 lbs/in³
Specific Gravity	N/A 2.70
¹ Average of tension and compression moduli. Compression modulus is about 2 percent greater than tension modulus. ² Ratings A through E are relative ratings in decreasing order of merit, based on exposures to sodium chloride solution by intermittent spraying or immersion. Alloys with A and B ratings can be used in industrial and seacoast atmospheres without protection. Alloys with C, D and E ratings generally should be protected at least on faying surfaces. ³ Stress-corrosion cracking ratings are based on service experience and on laboratory tests of specimens exposed to the 3.5% sodium chloride alternate immersion test. ⁴ Ratings A through D for Workability (cold), and A through E for Machinability, are relative ratings in decreasing order of merit. ⁵ Ratings A through D for Weldability and Brazeability are relative ratings. ⁶ A = Generally weldable by all commercial procedures and methods. B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance. C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties. ⁷ A = Generally weldable by all commercial procedures and methods. B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance. C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties. ⁸ A = Generally weldable by all commercial procedures and methods. B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance. C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.