Continental Steel and Tube Company
Continental Steel and Tube Company
P.O. BOX 030040
Fort Lauderdale, FL, 33303
Phone: 954.332.2290
Fax: 954.332.2296
Email: Sales@ContinentalSteel.com
Website: www.continentalsteel.com
Print Back
6061 is the least expensive and most versatile of the heat-treatable aluminum alloys. It has most of the good qualities of aluminum. It offers a range of good mechanical properties and good corrosion resistance. It can be fabricated by most of the commonly used techniques. In the annealed condition it has good workability. In the T4 condition fairly severe forming operations may be accomplished. The full T6 properties may be obtained by artificial aging. It is welded by all methods and can be furnace brazed. It is available in the clad form ("Alclad") with a thin surface layer of high purity aluminum to improve both appearance and corrosion resistance. Applications: This grade is used for a wide variety of products and applications from truck bodies and frames to screw machine parts and structural components. 6061 is used where appearance and better corrosion resistance with good strength are required.

6061-T6 Schedule 40
20' Lengths
ASTM B241 UNS A96061
Unit of Measure

Specifications

Material

 N/A Aluminum

Shapeform

 N/A Pipe

Series

 N/A 6061-T6

Grade

 N/A 6061

Temper

 N/A T6

Standard

 N/A Schedule 40

Nominal Size

 N/A 1/2 inches

Nominal Size

 N/A 0.5 inches12.7 mm

O.D.

 N/A 0.84 inches21.336 mm

I.D.

 N/A 0.622 inches15.7988 mm

Wall Thickness

 N/A 0.109 inches2.7686 mm

Weight

 N/A 0.2944 lbs/ft0.4381154816 kg/m

Weight per 20'

 N/A 5.888 lbs2.6707968 kg

ASTM Specification

 N/A ASME S241M ASME SB241 ASTM B241 Mil-P-25995 UNS A96061

Length

 N/A 20 ft

Density

 N/A 0.098 lbs/in³

Specific Gravity

 N/A 2.70

Typical Mechanical Properties

Ultimate Strength

 N/A 45 ksi

Yield Strength

 N/A 40 ksi

Elongation percent in 2 inches

 N/A 12

Hardness Brinnel Number

 N/A 95

Ultimate Shearing Strength

 N/A 30 ksi
Fatigue Endurance Limit1 N/A 14 ksi
Modulus of Elasticity2 N/A 10.0 x 103 ksi

Comparative Characteristics and Applications

Resistance to Corrosion - General3 N/A B

Stress Corrosion Cracking

 N/A A

Workability (Cold)

 N/A C

Mechinability

 N/A C
Brazeability4 N/A A
Gas Weldability5 N/A A
Arc Weldability6 N/A A
Resistance Spot and Seam Weldability7 N/A A

Applications

 N/A Heavy-duty structures requiring good corrosion resistance, truck and marine, railroad cars, furniture, pipelines

Aluminum Alloy Designations

N/A

    The aluminum industry uses a four-digit index system for the designation of its wrought aluminum alloys.
    As outlined below, the first digit indicates the alloy group according to the major alloying elements.

    1xxx Series
    In this group minimum aluminum content is 99% and there is no major alloying element. The second digit indicates modifications in impurity limits. If the second digit is zero, there is no special control on individual impurities. Digits 1 through 9, which are assigned consecutively as needed, indicate special control of one or more individual impurities. The last two digits indicate specific minimum aluminum content. Although the absolute minimum aluminum content in this group is 99%, the minimum for certain grades is higher than 99%, and the last two digits represent the hundredths of a per cent over 99. Thus, 1030 would indicate 99.30% minimum aluminum. without special control on individual impurities. The designations 1130, 1230, 1330, etc.. indicate the same purity with special control on one or more impurities. Likewise 1100 indicates minimum aluminum content of 99.00% with individual impurity control.

    2xxx through 9xxx Series
    The major alloying elements are indicated by the first digit, as follows:
      2xxx Copper
      3xxx Manganese
      4xxx Silicon
      5xxx Magnesium
      6xxx Magnesium and silicon
      7xxx Zinc
      8xxx Other element
      9xxx Unused series

    The second digit indicates alloy modification. If the second digit is zero. it indicates the original alloy: digits 1 through 9, which are assigned consecutively, indicate alloy modifications. The last two digits have no special significance, serving only to identify the different alloys in the group.

    Experimental Alloys
    Experimental alloys are designated according to the four digit system, but they are prefixed by the letter X. The prefix is dropped when the alloy becomes standard. During development, and before they are designated as experimental, new alloys are identified by serial numbers assigned by their originators. Use of the serial number is discontinued when the X number is assigned.
  • 1 Based on 500,000.000 cycles of completely reversed stress using the R. R. Moore-type of machine and specimen.
  • 2 Average of tension and compression moduli. Compression modulus is about 2 percent greater than tension modulus.
  • 3 Ratings A through E are relative ratings in decreasing order of merit, based on exposures to sodium chloride solution by intermittent spraying or immersion. Alloys with A and B ratings can be used in industrial and seacoast atmospheres without protection. Alloys with C, D and E ratings generally should be protected at least on faying surfaces.
  • 4 Ratings A through D for Weldability and Brazeability are relative ratings.
  • 5 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.
  • 6 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.
  • 7 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.